frigidaire high efficiency washer manual

See the installation instructions for further information on how to level your Laundry Center and remove shipping materials. Placing your laundry in the washer tub before starting the cycle will ensure detection and reduce vibration. Shut off the washer, wait for the safety lock to release, and redistribute the clothes evenly in the tub. If the load remains out of balance, try adding one or two similar items and restart the washer. Water temperatures may seem cooler than traditional laundry centers. There is an H for Hot and C for Cold embossed on the back of the unit for each hookups. Using only a cold (or only a hot) supply hose will result in water backflow through the valve and onto the floor. The unit will then stop what it is doing and unlock the lid when it is safe to reach inside the machine. To resume the cycle from where it left off, simply press the cycle selector again. Typically, the Normal Cycle will take 60-80 minutes. For small loads of 10 items or less, try using the Quick Wash cycle which only takes about 23-28 minutes, depending on load size. In the event that your washer encounters an unbalanced load, it will perform an extra rinse cycle to re-balance. This can add about 10-30 minutes to the cycle. See the FAQ on how to avoid out-of-balance problems. If your water pressure is low it can take longer for the tub to fill with water, which adds time to the wash cycle. See the FAQ on how to avoid Out-of-Balance conditions. The washer will beep once and lock to begin the sensory cycle after the Start button is pressed. Double-check that your machine has been installed properly by running through the checklist in the Installation Guide. Adding 1 or 2 laundry items to the load will help to balance the weight during spin cycles. This can add about 10-30 minutes to the cycle. Frigidaire Laundry Centers are High Efficiency machines that use significantly less water than traditional washing machines. HE- rated detergents are designed for lower water levels.

• frigidaire high efficiency washer manual, frigidaire high efficiency washer manual diagram, frigidaire high efficiency washer manual download, frigidaire high efficiency washer manual pdf, frigidaire high efficiency washer manual parts.

We appreciate your patience. They use less water and energy by incorporating elements such as low-profile agitators and sensory technology. Learn more about Energy Star guidelines here. Ensure that power is coming from the outlet and the electrical supply cord fits tightly in the wall. Your Laundry Center should be on its own circuit breaker and not shared with any other outlets or appliances. Note: Do not use an extension cord. Depending on the quality of the extension cord and the length, the power may be greatly reduced and not allow the washer to perform properly. For your safety, the door or lid of your washer must be completely closed for the washer to start. These high performance Laundry Centers with low-profile agitators are designed to use less water and energy while being gentle on your clothes. The low profile agitators also free up space for larger loads, making it easier to add and remove laundry. It is normal for the water level to appear lower than traditional washing machines. Frigidaire High Efficiency Laundry Centers rely on sensory technology to tune water levels and agitation cycles to your specific load size. The water level, agitation intensity and vibration tuning are set based on the load size that is detected. Water will enter the tub once the sensory cycle is complete. Frigidaire High Efficiency Laundry Centers are designed to use less water and energy. To maximize efficiency, the first 2 minutes of the cycle are spent sensing the load. When the sensing cycle is complete, the optimal amount of water will be dispensed to achive efficient cleaning performance. This will ensure that the chemicals are properly dissolved and mixed in the wash water. If your unit has a dispenser, simply pour fabric softener into the dispenser and make sure the Fabric Softener button or dial is in the “ON” position. If liquid fabric softener touches clothes directly, it could leave a stain that can be very difficult to remove.

You can refer to your Complete Owner’s Guide for more information. The washer must be level (both front to back and side to side), with each washer leg placed solidly on the floor. You can adjust the leveling legs by turning the legs slightly in or out until the washer is set solidly on the floor, then tighten the lock nuts. For maximum stability, leveling legs should not extend more than one-half inch below the washer bottom. It is not recommended that you install the washer on carpeting. You may refer to your Installation Instructions to remove five Shipping bolts, four plastic “P” clamps, one white spacer and four black spacers from the back of the washer. Make sure the Styrofoam shipping blocks have been removed from the bottom of the washer. Shut off the water, wait for the safety lock to release on the door, and redistribute the clothes evenly in the washer. If the load remains out of balance, simply add one or two similar items to the load and restart the washer. Belt buckles or other metal fasteners on items being washed may cause rattling or clanking sounds, too. You can fasten these items or turn garments inside out to reduce the sounds. Rattling or clanking may also be caused by foreign objects (such as coins) in the drum. If you think this is the cause, stop the washer and check for any objects in the drum. If none are present and the sound continues, we recommend running an empty load to see if the noise persists. This will allow you to determine if the noise is coming from the unit or an article that was being washed. If the noise is still present during the empty load, please contact us. This is normal, a pause occurs between the Wash and Spin cycles, with a longer pause occurring during the Soak cycle. With front load washers, normal pauses also occur as part of the reverse tumbling action.Check that your washer’s plug fits tightly into the wall outlet. Note: Do not use an extension cord.

Please refer to the installation instructions for further information. You should also check the exhaust duct to ensure it is free from clogs. If your load is too big or too small, it will take longer for your clothes to dry. You can use a dehumidifier near the dryer if needed. We appreciate your patience. Don’t forget to register your Frigidaire product. Once you have registered, you will receive useful information including easy access to your warranty and product care tips. Download the Complete Owner’s Guide on the Owner Support page for additional information on your product. To register your product you will need your model and serial number, which can be located on the inside of the door or door well, depending on the model. You will also need to provide the date of purchase as shown on your receipt. It’s always a good idea to save this information. You can also send your product registration card in the mail. If you have any questions, please contact Frigidaire at 1-800-374-4432. HE detergents are designed for front load washers like ours, which use lower water levels. They are also formulated to reduce soap suds and ensure proper cleaning. Non-HE detergents may cause excessive generation of soap suds and result in detergent residue on your clothing at the end of the cycle. Always refer to your detergent manufacturer’s instructions for the proper dosage. Do not fill any compartments in your dispenser beyond the maximum amount line. We do not recommend the use of detergent pods with our front load washers. We are unable to guarantee the pod will dissolve at the correct time during the wash cycle to ensure proper cleaning performance. If pods are used, please place the pod directly into the washer drum BEFORE placing laundry into the unit. This will help mix the detergent into the water. Do not place the pod in the detergent drawer as the gel coating may cause the detergent drawer to become clogged.

A If you are unable to resolve an issue or need more information, please contact us. It cannot be more than 96 inches high. If the drain hose has been taped (or sealed) into the standpipe, the seal should not be completely tight because the standpipe requires air for proper draining. If necessary, remove some of the tape on the seal to make an air path. The standpipe needs to be at least 1.Using too much detergent can also inhibit draining. If you suspect this is the case, please call your authorized servicer. If so, it will need to be cleaned; you may need to contact a plumber. If it is out of the standpipe, you will need to secure it. You can do this by bending the end to form a hook, placing the hooked end into the standpipe, and tying the hose to the standpipe or a faucet with a cable tie (one was supplied with the washer), strong filament tape or duct tape. Check by realigning the threads, make sure that the rubber sealing washers are in good shape and seated properly, and tighten the hose connections. If they are loose, you might need to reinstall or replace the rubber sealing washers. Using a non-HE detergent or using too much detergent in soft water can cause suds to overflow the washer. This may seem like a leak if the suds flow or drip onto the floor. To avoid this, use an HE detergent, and reduce the amount of detergent you use if your water is soft. To open it, simply stop the washer and wait 1 to 3 minutes for the safety lock to open. On a front load washer, the door will be locked during the entire wash cycle. Before tumbling starts, you can stop the washer and then wait for the water to drain off the window before opening the door. To open the door during the spin cycle, stop the washer and wait 1 to 3 minutes for the lock to release—do not force the door open. We appreciate your patience. They use less water and energy by incorporating elements such as low-profile agitators and sensory technology. Learn more about Energy Star guidelines here.

The power to the washer may be greatly reduced and not allow your washer to perform properly. For your safety, the washer will not operate when the door is not closed properly. If this is the case, reset the circuit breaker or replace the fuse (but do not increase the fuse capacity). If you have an overloaded circuit, please contact a qualified electrician. Is this normal? Because this type of washer is water efficient, it’s normal for the water level to always be below the bottom of the door. Frigidaire Front Load washers are designed to both maximize water usage and the cleaning of your laundry. You will notice significantly less water usage in your front load washer than you are used to seeing in other units, especially top-load washers. The addition of extra water may actually result in your laundry not being cleaned as well. Tumbling action and recirculating pumps help distribute the water and detergent to clean your laundry more efficiently. If you are unable to resolve an issue or need more information, please contact us. Depending on the water pressure in your home, which varies, you may want to avoid excessive water use elsewhere in your home while the washer is filling. To prevent siphoning off of incoming water, the standpipe cannot be too short; it must be at least 24 inches high. Be sure there is a gap between the drain hose and the standpipe, and that the standpipe is at least 1? inches in diameter. The drain hose should be securely inserted into the standpipe, but not so far down that it reaches the trap area of the standpipe plumbing. Rearrange the items in your load to allow proper spinning, possibly adding one or two similar items to help balance the load. A If the load is comprised of items that cannot be distributed around the drum, such as a single pillow or stuffed animal, the washer will not spin. Additional items will need to be added to the unit to better balance the weight of the load.

You should also check the exhaust duct to ensure it is free from clogs. If your load is too big or too small, it will take longer for your clothes to dry. You can use a dehumidifier near the dryer if needed. We appreciate your patience. Don’t forget to register your Frigidaire product. Once you have registered, you will receive useful information including easy access to your warranty and product care tips. Download the Complete Owner’s Guide on the Owner Support page for additional information on your product. To register your product you will need your model and serial number, which can be located on the inside of the door or door well, depending on the model. You will also need to provide the date of purchase as shown on your receipt. It’s always a good idea to save this information. You can also send your product registration card in the mail. If you have any questions, please contact Frigidaire at 1-800-374-4432. HE detergents are designed for front load washers like ours, which use lower water levels. They are also formulated to reduce soap suds and ensure proper cleaning. Non-HE detergents may cause excessive generation of soap suds and result in detergent residue on your clothing at the end of the cycle. Always refer to your detergent manufacturer’s instructions for the proper dosage. Do not fill any compartments in your dispenser beyond the maximum amount line. We do not recommend the use of detergent pods with our front load washers. We are unable to guarantee the pod will dissolve at the correct time during the wash cycle to ensure proper cleaning performance. If pods are used, please place the pod directly into the washer drum BEFORE placing laundry into the unit. This will help mix the detergent into the water. Do not place the pod in the detergent drawer as the gel coating may cause the detergent drawer to become clogged. You can refer to your Complete Owner’s Guide for more information.

The washer must be level (both front to back and side to side), with each washer leg placed solidly on the floor. You can adjust the leveling legs by turning the legs slightly in or out until the washer is set solidly on the floor, then tighten the lock nuts. For maximum stability, leveling legs should not extend more than one-half inch below the washer bottom. It is not recommended that you install the washer on carpeting. You may refer to your Installation Instructions to remove five Shipping bolts, four plastic “P” clamps, one white spacer and four black spacers from the back of the washer. Make sure the Styrofoam shipping blocks have been removed from the bottom of the washer. Shut off the water, wait for the safety lock to release on the door, and redistribute the clothes evenly in the washer. If the load remains out of balance, simply add one or two similar items to the load and restart the washer. Belt buckles or other metal fasteners on items being washed may cause rattling or clanking sounds, too. You can fasten these items or turn garments inside out to reduce the sounds. Rattling or clanking may also be caused by foreign objects (such as coins) in the drum. If you think this is the cause, stop the washer and check for any objects in the drum. If none are present and the sound continues, we recommend running an empty load to see if the noise persists. This will allow you to determine if the noise is coming from the unit or an article that was being washed. If the noise is still present during the empty load, please contact us. This is normal, a pause occurs between the Wash and Spin cycles, with a longer pause occurring during the Soak cycle. With front load washers, normal pauses also occur as part of the reverse tumbling action.Check that your washer’s plug fits tightly into the wall outlet. Note: Do not use an extension cord. The power to the washer may be greatly reduced and not allow your washer to perform properly.

Ensure that power is coming from the outlet and the electrical supply cord fits tightly in the wall. Your Laundry Center should be on its own circuit breaker and not shared with any other outlets or appliances. Note: Do not use an extension cord. Depending on the quality of the extension cord and the length, the power may be greatly reduced and not allow the washer to perform properly. For your safety, the door or lid of your washer must be completely closed for the washer to start. These high performance Laundry Centers with low-profile agitators are designed to use less water and energy while being gentle on your clothes. The low profile agitators also free up space for larger loads, making it easier to add and remove laundry. It is normal for the water level to appear lower than traditional washing machines. Frigidaire High Efficiency Laundry Centers rely on sensory technology to tune water levels and agitation cycles to your specific load size. The water level, agitation intensity and vibration tuning are set based on the load size that is detected. Water will enter the tub once the sensory cycle is complete. Frigidaire High Efficiency Laundry Centers are designed to use less water and energy. To maximize efficiency, the first 2 minutes of the cycle are spent sensing the load. When the sensing cycle is complete, the optimal amount of water will be dispensed to achive efficient cleaning performance. This will ensure that the chemicals are properly dissolved and mixed in the wash water. If your unit has a dispenser, simply pour fabric softener into the dispenser and make sure the Fabric Softener button or dial is in the “ON” position. If liquid fabric softener touches clothes directly, it could leave a stain that can be very difficult to remove. See the installation instructions for further information on how to level your Laundry Center and remove shipping materials.

Placing your laundry in the washer tub before starting the cycle will ensure detection and reduce vibration. Shut off the washer, wait for the safety lock to release, and redistribute the clothes evenly in the tub. If the load remains out of balance, try adding one or two similar items and restart the washer. Water temperatures may seem cooler than traditional laundry centers. There is an H for Hot and C for Cold embossed on the back of the unit for each hookups. Using only a cold (or only a hot) supply hose will result in water backflow through the valve and onto the floor. The unit will then stop what it is doing and unlock the lid when it is safe to reach inside the machine. To resume the cycle from where it left off, simply press the cycle selector again. Typically, the Normal Cycle will take 60-80 minutes. For small loads of 10 items or less, try using the Quick Wash cycle which only takes about 23-28 minutes, depending on load size. In the event that your washer encounters an unbalanced load, it will perform an extra rinse cycle to re-balance. This can add about 10-30 minutes to the cycle. See the FAQ on how to avoid out-of-balance problems. If your water pressure is low it can take longer for the tub to fill with water, which adds time to the wash cycle. See the FAQ on how to avoid Out-of-Balance conditions. The washer will beep once and lock to begin the sensory cycle after the Start button is pressed. Double-check that your machine has been installed properly by running through the checklist in the Installation Guide. Adding 1 or 2 laundry items to the load will help to balance the weight during spin cycles. This can add about 10-30 minutes to the cycle. Frigidaire Laundry Centers are High Efficiency machines that use significantly less water than traditional washing machines. HE- rated detergents are designed for lower water levels. Please refer to the installation instructions for further information.

For your safety, the washer will not operate when the door is not closed properly. If this is the case, reset the circuit breaker or replace the fuse (but do not increase the fuse capacity). If you have an overloaded circuit, please contact a qualified electrician. Is this normal? Because this type of washer is water efficient, it’s normal for the water level to always be below the bottom of the door. Frigidaire Front Load washers are designed to both maximize water usage and the cleaning of your laundry. You will notice significantly less water usage in your front load washer than you are used to seeing in other units, especially top-load washers. The addition of extra water may actually result in your laundry not being cleaned as well. Tumbling action and recirculating pumps help distribute the water and detergent to clean your laundry more efficiently. If you are unable to resolve an issue or need more information, please contact us. Depending on the water pressure in your home, which varies, you may want to avoid excessive water use elsewhere in your home while the washer is filling. To prevent siphoning off of incoming water, the standpipe cannot be too short; it must be at least 24 inches high. Be sure there is a gap between the drain hose and the standpipe, and that the standpipe is at least 1? inches in diameter. The drain hose should be securely inserted into the standpipe, but not so far down that it reaches the trap area of the standpipe plumbing. Rearrange the items in your load to allow proper spinning, possibly adding one or two similar items to help balance the load. A If the load is comprised of items that cannot be distributed around the drum, such as a single pillow or stuffed animal, the washer will not spin. Additional items will need to be added to the unit to better balance the weight of the load. A If you are unable to resolve an issue or need more information, please contact us. It cannot be more than 96 inches high.

If the drain hose has been taped (or sealed) into the standpipe, the seal should not be completely tight because the standpipe requires air for proper draining. If necessary, remove some of the tape on the seal to make an air path. The standpipe needs to be at least 1.Using too much detergent can also inhibit draining. If you suspect this is the case, please call your authorized servicer. If so, it will need to be cleaned; you may need to contact a plumber. If it is out of the standpipe, you will need to secure it. You can do this by bending the end to form a hook, placing the hooked end into the standpipe, and tying the hose to the standpipe or a faucet with a cable tie (one was supplied with the washer), strong filament tape or duct tape. Check by realigning the threads, make sure that the rubber sealing washers are in good shape and seated properly, and tighten the hose connections. If they are loose, you might need to reinstall or replace the rubber sealing washers. Using a non-HE detergent or using too much detergent in soft water can cause suds to overflow the washer. This may seem like a leak if the suds flow or drip onto the floor. To avoid this, use an HE detergent, and reduce the amount of detergent you use if your water is soft. To open it, simply stop the washer and wait 1 to 3 minutes for the safety lock to open. On a front load washer, the door will be locked during the entire wash cycle. Before tumbling starts, you can stop the washer and then wait for the water to drain off the window before opening the door. To open the door during the spin cycle, stop the washer and wait 1 to 3 minutes for the lock to release—do not force the door open. We appreciate your patience. Don’t forget to register your Frigidaire product. Once you have registered, you will receive useful information including easy access to your warranty and product care tips. Download the Complete Owner’s Guide on the Owner Support page for additional information on your product.

To register your product you will need your model and serial number, which can be located on the inside of the door or door well, depending on the model. You will also need to provide the date of purchase as shown on your receipt. It’s always a good idea to save this information. You can also send your product registration card in the mail. If you have any questions, please contact Frigidaire at 1-800-374-4432. HE detergents are designed for front load washers like ours, which use lower water levels. They are also formulated to reduce soap suds and ensure proper cleaning. Non-HE detergents may cause excessive generation of soap suds and result in detergent residue on your clothing at the end of the cycle. Always refer to your detergent manufacturer’s instructions for the proper dosage. Do not fill any compartments in your dispenser beyond the maximum amount line. We do not recommend the use of detergent pods with our front load washers. We are unable to guarantee the pod will dissolve at the correct time during the wash cycle to ensure proper cleaning performance. If pods are used, please place the pod directly into the washer drum BEFORE placing laundry into the unit. This will help mix the detergent into the water. Do not place the pod in the detergent drawer as the gel coating may cause the detergent drawer to become clogged. You can refer to your Complete Owner’s Guide for more information. The washer must be level (both front to back and side to side), with each washer leg placed solidly on the floor. You can adjust the leveling legs by turning the legs slightly in or out until the washer is set solidly on the floor, then tighten the lock nuts. For maximum stability, leveling legs should not extend more than one-half inch below the washer bottom. It is not recommended that you install the washer on carpeting.

You may refer to your Installation Instructions to remove five Shipping bolts, four plastic “P” clamps, one white spacer and four black spacers from the back of the washer. Make sure the Styrofoam shipping blocks have been removed from the bottom of the washer. Shut off the water, wait for the safety lock to release on the door, and redistribute the clothes evenly in the washer. If the load remains out of balance, simply add one or two similar items to the load and restart the washer. Belt buckles or other metal fasteners on items being washed may cause rattling or clanking sounds, too. You can fasten these items or turn garments inside out to reduce the sounds. Rattling or clanking may also be caused by foreign objects (such as coins) in the drum. If you think this is the cause, stop the washer and check for any objects in the drum. If none are present and the sound continues, we recommend running an empty load to see if the noise persists. This will allow you to determine if the noise is coming from the unit or an article that was being washed. If the noise is still present during the empty load, please contact us. This is normal, a pause occurs between the Wash and Spin cycles, with a longer pause occurring during the Soak cycle. With front load washers, normal pauses also occur as part of the reverse tumbling action.Check that your washer’s plug fits tightly into the wall outlet. Note: Do not use an extension cord. The power to the washer may be greatly reduced and not allow your washer to perform properly. For your safety, the washer will not operate when the door is not closed properly. If this is the case, reset the circuit breaker or replace the fuse (but do not increase the fuse capacity). If you have an overloaded circuit, please contact a qualified electrician. Is this normal? Because this type of washer is water efficient, it’s normal for the water level to always be below the bottom of the door.

Frigidaire Front Load washers are designed to both maximize water usage and the cleaning of your laundry. You will notice significantly less water usage in your front load washer than you are used to seeing in other units, especially top-load washers. The addition of extra water may actually result in your laundry not being cleaned as well. Tumbling action and recirculating pumps help distribute the water and detergent to clean your laundry more efficiently. If you are unable to resolve an issue or need more information, please contact us. Depending on the water pressure in your home, which varies, you may want to avoid excessive water use elsewhere in your home while the washer is filling. To prevent siphoning off of incoming water, the standpipe cannot be too short; it must be at least 24 inches high. Be sure there is a gap between the drain hose and the standpipe, and that the standpipe is at least 1? inches in diameter. The drain hose should be securely inserted into the standpipe, but not so far down that it reaches the trap area of the standpipe plumbing. Rearrange the items in your load to allow proper spinning, possibly adding one or two similar items to help balance the load. A If the load is comprised of items that cannot be distributed around the drum, such as a single pillow or stuffed animal, the washer will not spin. Additional items will need to be added to the unit to better balance the weight of the load. A If you are unable to resolve an issue or need more information, please contact us. It cannot be more than 96 inches high. If the drain hose has been taped (or sealed) into the standpipe, the seal should not be completely tight because the standpipe requires air for proper draining. If necessary, remove some of the tape on the seal to make an air path. The standpipe needs to be at least 1.Using too much detergent can also inhibit draining. If you suspect this is the case, please call your authorized servicer.